DF Sintered Stone / Fabrication & Procurement
Full Body Sintered Stone for Kitchen Edge Profiling: 12mm and 20mm Procurement Specifications
Full body sintered stone slabs carry body coloration through their thickness, reducing the contrasting substrate exposed by beveling, bullnose profiling, and edge machining. Through-body veining is a separate specification: buyers must verify that the selected pattern penetrates the slab rather than assuming that a color-matched body reproduces every surface vein. For 12mm and 20mm kitchen countertops, purchasing decisions should combine a machined edge sample, thickness-specific test reports and an approved fabrication procedure.
The Glaze vs. Full Body Dilemma in Mitering
Body Color and Vein Penetration Are Different Acceptance Criteria
A digitally decorated slab can reproduce a stone pattern on its face while retaining a differently colored body. When machining removes that decorated surface, the exposed section may contrast with the countertop.
A color-matched body reduces this contrast. A through-body veined product additionally carries decorative variation into the section, although vein position, width, and direction can change with depth. "Full body" therefore requires a physical definition in the purchase order.
Table 01 / Slab Construction and Edge Exposure
| Slab construction | Appearance after machining | Procurement check | Edge-design implication |
|---|---|---|---|
| Surface decoration over a contrasting body | Base material becomes visible below the face. | Inspect a freshly cut cross-section. | Mitered returns can conceal much of the exposed section. |
| Color-matched body with surface decoration | Body tone coordinates with the face; printed veins may stop. | Compare the face, straight edge, and bevel. | Suitable where body-color coordination is sufficient. |
| Through-body veined construction | Decorative variation extends into the section. | Inspect sections in two perpendicular directions. | Supports exposed profiles where section veining is required. |
DF's full body sintered stone slabs collection should be specified by product code, thickness, finish, and approved cross-section sample. The purchase specification should distinguish body coloration from through-body veining.
A Miter Joint Still Requires Adhesive and Alignment Control
A 45-degree miter joins two machined edges. Body coloration can reduce visual contrast at the arris, but it does not eliminate the adhesive line, cutting error, or assembly movement.
Before approving production, assemble a corner using the actual slab batch and proposed adhesive. Inspect:
- Face-to-return vein alignment.
- Adhesive color after full cure.
- Chipping along both mitered edges.
- Joint width and corner straightness.
- The protective edge radius or chamfer shown on the shop drawing.
A 60mm drop-apron assembled from 12mm material remains a fabricated edge assembly. Its apparent height must not be specified as 60mm solid slab thickness.
Micro-Pigment Dispersion in 12mm and 20mm Slabs
Powder Preparation Determines Section Consistency
Where wet preparation is used, a wet grinding ball mill reduces and homogenizes the mineral suspension before subsequent processing. Body coloration depends on pigment selection, dispersion, powder preparation, and feeding consistency.
Relevant mineral chemistry includes silica, SiO2; alumina-bearing constituents, commonly expressed as Al2O3; and feldspathic fluxes containing alkali oxides. These formulas identify constituent chemistry, not a disclosed DF production recipe.
For procurement, "micro-pigment dispersion technology" should be supported by measurable controls:
- Particle-size distribution and measurement method.
- Pigment dosage and batch traceability.
- Cross-section color consistency.
- Fired shrinkage and final thickness distribution.
- Repeatability between the approved sample and production lot.
Uniform pigment dispersion produces consistent body color. Deliberately structured powder distribution produces through-body decorative variation. These are related manufacturing operations with different visual acceptance criteria.
Compaction Equipment Must Be Described Accurately
The SACMI Continua+ continuous pressing system uses continuous powder compaction. SACMI describes its PCR compactor as operating through converging motorized belts and intermediate rollers; it should not automatically be described as a conventional "10,000+ metric ton hydraulic compaction" press.
Likewise, "1200°C roller kiln thermal sintering" describes a nominal firing condition, not a finished-product performance certificate. Buyers should request the applicable production route and batch test evidence rather than infer edge strength from press tonnage or kiln temperature.
Establish Test-Based Purchasing Thresholds
Specification StatusThe following values are proposed procurement targets, not verified performance declarations for every DF product. Incorporate them into the purchase contract only after the selected code, thickness, and finish have supporting laboratory reports.
Table 02 / Physical Properties and Test Evidence
| Property | Proposed target/reporting requirement | Test reference | Engineering interpretation |
|---|---|---|---|
| Water absorption | ≤0.05% | EN ISO 10545-3 | Does not establish stain resistance or adhesive compatibility. |
| Bulk density | ≥2.40 g/cm³ | EN ISO 10545-3 | Supports mass calculations; does not establish allowable span. |
| Modulus of rupture | ≥50 MPa | EN ISO 10545-4 | Requires thickness, specimen details and breaking strength. |
| Scratch hardness | Mohs 6–7, if substantiated | State the actual scratch-test method | Does not quantify edge-impact resistance. |
| Thermal shock resistance | Report outcome and observed damage | EN ISO 10545-9 | Does not establish unrestricted hot-pan contact. |
| Chemical resistance | Report reagent-specific classification | ISO 10545-13 | An isolated "Class A" statement is insufficient. |
| Dimensions and flatness | Contract limits with an agreed sampling plan | EN ISO 10545-2 | Measure thickness variation, curvature and warpage separately. |
ISO 10545-3 covers water absorption and density measurements; ISO 10545-4 determines modulus of rupture and breaking strength. ISO 10545-13 evaluates chemical resistance at room temperature. These methods measure different properties and should remain separate entries in the technical submittal.
UV resistance under DIN 51094 and Class A1 non-combustibility under EN 13501-1 should appear only where applicable evidence supports the supplied product. A classification for an unbacked slab must not be extended automatically to a bonded countertop assembly.
Fabricator Notice
Evaluate the Machined Edge Before Ordering the Batch
Request 12mm and 20mm cross-section samples, a trial-machined edge and the applicable physical Technical Data Sheets from East Phenix. Include your intended profile and tooling so the sample evaluation addresses the actual machining operation.
Reference the selected product from the DF full body collection when submitting your sample requirements.
Bevel, Bullnose and Waterfall Edge Engineering
Select Thickness Against the Finished Assembly
For identical material properties, width and support conditions, rectangular-section bending stiffness varies with thickness cubed. Increasing thickness from 12mm to 20mm gives a theoretical stiffness ratio of approximately 4.63. This calculation does not authorize a particular overhang: cutouts, supports, defects and load position still govern the assembly.
Table 03 / Thickness, Mass and Profile Geometry
| Engineering variable | 12mm slab | 20mm slab |
|---|---|---|
| Nominal format considered | 1600 × 3200mm | 1600 × 3200mm |
| Area per slab | 5.12m² | 5.12m² |
| Calculated mass per square meter | 28.8kg | 48.0kg |
| Calculated mass per slab | 147.5kg | 245.8kg |
| Relative section stiffness | 1.00 | 4.63 |
| Full bullnose geometry before allowance | Nominal R6mm | Nominal R10mm |
| Primary fabrication consideration | Handling support around cutouts and narrow rails. | Greater lifting mass and machining volume. |
Calculations use an assumed density of 2,400 kg/m³ and exclude packaging, adhesive, backing and reinforcement.
For DF's 20mm coloured body sintered stone slabs, approve the exposed section and finished profile together. A thicker slab provides more profiling depth, but a highly polished curved edge may reflect light differently from the factory-finished face.
Internal Tension Relief Cutting Comes Before Cutouts
- Inspect and support the slab. Use a flat, clean cutting bed with full support. Inspect transport damage and record slab identification before machining.
- Complete the perimeter relief sequence. Place the first relief cut along the long perimeter, followed by a perpendicular perimeter cut, using the manufacturer's trim allowance.
- Drill internal corner radii before connecting cuts. Avoid unsupported internal plunges, extended saw overcuts and notches at cutout corners.
- Approve the first machined component. Check edge chipping, cutout geometry and dimensional accuracy before releasing repeated components.
A proposed R10mm internal corner, produced with a nominal Ø20mm core tool, provides a reviewable starting geometry. Confirm it against the appliance template and the material manufacturer's requirements before releasing drawings.
Record RPM, Feed Rate and Waterjet Pressure
A 5-axis CNC bridge saw provides angular positioning; it does not compensate for an unsuitable blade, inadequate coolant, or slab movement.
Published Cosentino fabrication guidance provides examples of the specificity required: approximately 2,200 RPM for a 14-inch blade, straight feeds of approximately 508–1,143mm/min depending on color, and CNC milling examples of 3,500–4,500 RPM at 180–210mm/min. These are Dekton-specific reference settings, not approved DF machining instructions.
Table 04 / Required Machining Process Records
| Operation | Parameters to fix before production |
|---|---|
| Straight bridge-saw cutting | Blade model and diameter, RPM, feed in mm/min, coolant delivery and entry/exit reduction. |
| 45-degree miter beveling | Blade suitability, angular calibration, feed reduction and retained edge geometry. |
| Corner drilling | Core-bit construction, diameter, RPM, feed, coolant and backing support. |
| CNC profiling | Tool sequence, stock removal per pass, RPM and feed. |
| Abrasive waterjet cutting | Pressure in bar, piercing pressure, feed, nozzle/orifice sizes and abrasive flow. |
For waterjet trial planning, 3,500 bar is a published reference pressure in Neolith fabrication guidance, which also requires reduced pressure for drilling and radiused internal corners. It must not be adopted as a DF production setting without material-specific trials.
An electroplated diamond core bit should be used only where its supplier approves the specific sintered material and operation. Select tooling by demonstrated cutting performance rather than by coating description alone.
Workshop ControlUse wet processing and effective exposure controls. Full body construction does not establish that the slab is free of crystalline silica.
Waterfall Panels Need a Support and Movement Detail
Continuous bookmatched veining requires slab-face selection and a documented cutting layout. Body coloration does not automatically align a horizontal top with its vertical return.
Dry-assemble the waterfall corner before bonding. Specify the load path, floor clearance or bearing condition, adhesive, joint geometry, and installation sequence.
C2TE S1 or S2 tile adhesive classifications may be relevant to a bonded cladding detail; they do not establish suitability for a structural miter joint. Likewise, an undercut mechanical anchor or kerf requires an engineered fixing detail rather than an improvised groove in a thin edge.
Commercial Application Reviews
The following are illustrative engineering scenarios, not claims of completed DF projects.
Multi-Unit Kitchens: Repeated Exposed Bevels
For an apartment package using 12mm countertops, the purchasing issue is repeatability across many machined edges.
Approve a retained reference sample showing the face, bevel, and section. Require slab identification on the cutting schedule and inspect the first completed unit before batch fabrication. Measure edge chipping, profile geometry, and face-to-section color coordination against that reference.
Hospitality Kitchens: Profiled 20mm Countertops
For a hospitality package using a 20mm bullnose, approve the profile after the complete grinding and finishing sequence.
Inspect the curved section under the intended lighting. The relevant acceptance question is whether body tone, exposed veining and edge sheen meet the mock-up-not whether the unmachined slab face alone was approved.
Branded Kitchen Displays: Bookmatched Waterfall Returns
For an OEM showroom island, reserve the required A/B faces before cutting. Photograph and label the dry layout, including the top, return and backsplash where applicable.
Approval should cover both vein alignment and the visible adhesive joint. A replacement panel must be checked against the original layout rather than selected solely by product name.
Ordering Specifications from a China Factory
Separate Published Product Data from Contract Commitments
DF publishes selected 1600 × 3200mm full body products in 12mm and 20mm. Its listed examples include a 10-slab MOQ and a 7–15-day lead time. Confirm these terms for the selected code and order; they do not establish an OEM development schedule or universal mixed-color MOQ.
A purchase order should identify:
- Product code, face designation, finish, and body construction.
- Nominal dimensions, thickness and agreed inspection limits.
- Required test reports and approved machined reference sample.
- CAD drawings, cutout radii, edge profiles and vein layout.
- Quantity by code and thickness, including replacement allocation.
- Packing arrangement, gross mass, loading port and Incoterm.
- Inspection, damage-reporting and claim documentation requirements.
Control Thickness and Flatness Independently
"12mm nominal" is not a thickness tolerance. Record measurements at agreed positions and specify how edge variation is treated.
Similarly, a single flatness statement should not combine center curvature, edge curvature and warpage. Establish numerical limits using the selected product's capability data, the EN ISO 10545-2 measurement procedure and the fabrication drawing.
For mitered work, inspect the mating strips as well as the parent slab. Variation between those pieces can affect joint closure even where individual thickness measurements fall within the contract limit.
Calculate FCL Payload Before Fixing Slab Quantity
At the assumed density of 2,400 kg/m³, the following calculations describe stone mass only:
Table 05 / Illustrative FCL Mass Calculations
| Slab thickness | Illustrative quantity | Total slab area | Calculated stone mass |
|---|---|---|---|
| 12mm | 176 slabs | 901.12m² | Approximately 25.95 tonnes |
| 20mm | 110 slabs | 563.20m² | Approximately 27.03 tonnes |
Slab format: 1600 × 3200mm. Quantities above are calculation examples, not approved payloads or guaranteed loading capacities.
Add the measured mass of A-frames, packaging, restraints and accessories before checking the container's actual payload plate, carrier restrictions and road limits.
For mixed-thickness FCL orders, calculate each line separately. Place compatible slab groups on rated A-frame steel racks with clean, non-staining EPE pearl-foam contact protection and protected edges. Steel straps must secure the bundle without bearing directly against unprotected slab corners.
The loading plan must address rack anchorage, longitudinal and transverse restraint, floor loading, weight distribution, and unloading access. Record loading photographs and verified gross mass.
Lifting and UnloadingAt the terminal, lift the container through its designated lifting system. During slab unloading, use rated rack lifting points or approved slab-handling equipment; packing straps are not lifting slings.
OEM / FCL Enquiry
Submit the Drawing, Quantity and Inspection Criteria
Send DF Sintered Stone your product codes, 12mm/20mm quantities, edge drawings, destination port, and required inspection criteria. Request a quotation with itemized fabrication scope, test documentation, packing mass, and a container loading plan from Xiamen East Phenix Imp.& Exp. Co., Ltd.
Review the full body slab collection and identify the product codes required for your enquiry.
B2B Procurement FAQ
DF lists a 10-slab MOQ for selected 1600 × 3200mm full body products, equivalent to 51.20m². Obtain written confirmation for each product code, thickness, and finish. Mixed-color orders, fabricated components, and OEM patterns require their own quantity and pricing confirmation before purchase-order release.
How should buyers calculate a mixed 12mm and 20mm container load?Use 28.8kg/m² for 12mm and 48.0kg/m² for 20mm only when calculating at an assumed density of 2.40g/cm³. Add measured rack and packaging mass, then check the specific container and route limits. Approve a restraint plan; no universal damage-free loading percentage applies.
Which thickness and flatness tolerances should a countertop purchase order state?Specify 12mm or 20mm nominal thickness, numerical deviation limits, thickness variation, and separate flatness limits measured under EN ISO 10545-2. Require signed inspection results before dispatch. Neither nominal thickness nor a product-family description establishes an acceptable ±mm tolerance for a particular countertop fabrication contract.
